HP Pagewide Pro 352dw Wireless Setup Guide

The new HP PageWide 352dw,452dw,552dw business portfolio will be available through channel partners and at select retail stores. In addition, the new portfolio increases the number of managed devices designed for contractual channel partners and managed print services engagements. These contractual HP PageWide printers enable HP channel partners to provide low cost of operation with HP’s highest capacity supplies, a three-year print head warranty, higher speeds and RMPV on select models, as well as integration with HP JetAdvantage Management and third-party tools. By optimizing managed HP PageWide devices for contractual agreements, HP provides channel partners with new opportunities to deliver higher customer satisfaction.
Related Printer: HP Pagewide Pro 452dw, HP PageWide 552dw
HP Pagewide Pro 352dw Wireless Setup

HP Pagewide Pro 352 Wireless Setup Network Computer Using USB Cable

You can use a USB cable to connect HP PageWide 352 to a computer. This product supports a USB 2.0 connection. Use an A-to-B type USB cable. HP recommends using a cable that is no longer than 2 m (6.5 ft). Do not connect the USB cable until the installation software prompts you to connect it.
  1. Quit all open programs on the computer.
  2. Install the printer software from 123.hp.com/pagewide (recommended) or from the HP software CD provided with the printer, and follow the onscreen instructions. If you are installing on a Mac, click About HP Easy Start to install the software.
  3. When prompted, select the USB-Connect the printer to the computer using a USB cable option, and then click the Next button. A dialog box displays a warning that Web Services (HP ePrint and print Apps) are unavailable with a USB installation. Click Yes to proceed with the USB installation, or click No to cancel it.
  4. When the software prompts you, connect the Type B end of the USB cable to the connection port (1) at the rear of the product.
  5. When the installation is complete, print a page from any program to make sure that the printing software is correctly installed.

HP Pagewide Pro 352dw Wireless Setup Network

The HP PageWide 352dw supports connection to either a wired or a wireless network.
Supported network protocols, HP Pagewide Pro 352dw Wireless Setup Wired Network
Use this procedure to install the product on a wired network using Windows.
  1. Connect the Ethernet cable to the product and to the network. Turn the product on.
  2. Wait for 60 seconds before continuing. During this time, the network recognizes the product and assigns an IP address or host name for the product.
  3. Open the control panel dashboard (swipe the dashboard tab at the top of any screen downward, or touch the dashboard area on the home screen).
  4. On the control panel dashboard, touch to display the IP address. Touch Print Details to print a page with the IP address.

HP Pagewide Pro 352dw Wireless Setup Network (wireless models only)

You can connect the product to a wireless network using one of the following methods.
  • To connect the product to a wireless network using the Wireless Setup Wizard
  • To connect the product to a wireless network using WPS
  • To connect the product to a wireless network manually
If your wireless router does not support Wi-Fi Protected Setup (WPS), obtain the wireless router network settings from your system administrator, or complete the following tasks.
  • Obtain the wireless network name or service set identifier (SSID).
  • Determine the security password or encryption key for the wireless network.
NOTE: Before installing the product software, make sure the product is not connected to the network using an Ethernet cable.

HP Pagewide Pro 352dw Wireless Setup Wizard

The Wireless Setup Wizard is the best method for installing the product on a wireless network.
  1. Open the control panel dashboard (swipe the dashboard tab at the top of any screen downward, or touch the dashboard area on the home screen).
  2. On the control panel dashboard, touch .
  3. Touch Network Setup, and then touch Wireless Settings.
  4. Touch Wireless Setup Wizard.
  5. The product scans for available wireless networks and returns a list of network names (SSIDs). Select the SSID for your wireless router from the list if it is available. If the SSID for your wireless router is not in the list, touch Enter SSID. When prompted for the type of network security, select the option that your wireless router uses. A keypad opens on the control panel display.
  6. Do one of the following:If your wireless router uses WPA security, type the passphrase on the keypad. If your wireless router uses WEP security, type the key on the keypad.
  7. Touch OK , and wait while the product establishes a connection with the wireless router. Establishing the wireless connection can take a few minutes.

HP Pagewide Pro 352dw Setup Wireless Network Using WPS

Before you can connect HP PageWide 352dw wireless network using WPS, make sure you have the following:
  • A wireless 802.11b/g/n network that includes a WPS-enabled wireless router or access point.
  • NOTE: The printer supports only connections using 2.4GHz.
  • A computer connected to the wireless network that you intend to connect the printer to. Be sure you have installed the HP printer software on the computer.
If you have a WPS router with a WPS push button, follow the Push Button method. If you are not certain your router has a push button, follow the PIN method.

Push Button method
  1. On the control panel, press and hold on the printer for more than three seconds to start WPS push mode. The indicator starts blinking.
  2. Press the WPS button on your router.
  3. The HP 352 begins a timer for approximately two minutes while a wireless connection is established.
PIN method
  1. Locate the WPS PIN.
  2. Open the control panel dashboard (swipe the dashboard tab at the top of any screen downward, or touch the dashboard area on the home screen).
  3. On the control panel dashboard, touch .
  4. Touch Network Setup, and then touch Wireless Settings.
  5. Touch Wi-Fi Protected Setup, and then touch PIN.
  6. On the control panel, press and hold on the printer for more than three seconds to start WPS push mode. The indicator starts blinking.
  7. Open the configuration utility or software for the wireless router or wireless access point, and then enter the WPS PIN.
  8. For more information about using the configuration utility, see the documentation provided with the router or wireless access point.
  9. Wait for about two minutes. If the printer connects successfully, the indicator stops blinking but remains lit.

HP Pagewide Pro 352dw Wireless Setup Wireless Network Manually

During the first 120 minutes of  setup, or after resetting the HP Pagewide Pro 352dw network defaults (and without a network cable attached to the product), the product's wireless radio will broadcast a wireless setup network for the product. The name of this network is “HP-Setup-xx-[product name]”.
  • The “xx” in the network name is the last two characters of the product's MAC address. The product name is HP PageWide Pro 352dw.
  1. From a wireless enabled product, connect to the setup network for the device.
  2. Open a web browser while connected to this setup network, and open the HP Embedded Web Server (EWS) using the following IP address. ● 192.168.223.1
  3. Find the Wireless Setup Wizard in the EWS and follow the instructions to manually connect the product. The product uses Automatic DHCP by default.

HP Pagewide Pro 352dw Wireless SetupUse Wi-Fi Direct to connect a computer or device to the HP PageWide 352dw

With Wi-Fi Direct, you can print wirelessly from a computer, smart phone, tablet, or other wireless-capable device without connecting to an existing wireless network. Guidelines for using Wi-Fi Direct
● Make sure your computer or mobile device has the necessary software.
  • If you are using a computer, make sure you have installed the printer software from 123.hp.com/pagewide (recommended) or from the HP software CD provided with the printer.
  • If you have not installed the HP printer software on the computer, connect to Wi-Fi Direct first and then install the printer software. Select Wireless when prompted by the printer software for a connection type.
  • If you are using a mobile device, make sure you have installed a compatible printing app. For more information about mobile printing, visit the HP Mobile Printing website.
● Make sure Wi-Fi Direct for your printer is turned on.
● Up to five computers and mobile devices can use the same Wi-Fi Direct connection.
● Wi-Fi Direct can be used while the printer is also connected either to a computer using a USB cable or to a network using a wireless connection.
● Wi-Fi Direct cannot be used to connect a computer, mobile device, or printer to the Internet.

To turn on Wi-Fi Direct
  1. Open the control panel dashboard (swipe the dashboard tab at the top of any screen downward, or touch the dashboard area on the home screen).
  2. On the control panel dashboard, touch .
  3. Touch .
  4. If the display shows that Wi-Fi Direct is off, touch Wi-Fi Direct and switch it on.
 TIP: You can also turn on Wi-Fi Direct from the EWS. For more information about using the EWS, see HP Pagewide Pro 352dw Setup Embedded Web Server.

HP Pagewide Pro 352dw Wireless Setup Manually TCP/IP From Control Panel

Use the control panel menus to manually set an IPv4 address, subnet mask, and default gateway.
  1. Open the control panel dashboard (swipe the dashboard tab at the top of any screen downward, or touch the dashboard area on the home screen).
  2. On the control panel dashboard, touch .
  3. Touch Network Setup, and then touch Ethernet Settings.
  4. Touch Advanced Settings, and then touch IP Settings.
  5. Touch Manual, and then touch IP Address.
  6. Using the numeric keypad, do the following:
  • Enter the IP address, and touch Done .
  • Enter the subnet mask, and touch Done .
  • Enter the default gateway, and touch Done .
      7. Touch Apply.

HP Pagewide Pro 352dw Setup Link speed and duplex settings

This information applies only to Ethernet (wired) networks. It does not apply to wireless networks.The link speed and communication mode of the print server must match the network hub. For most situations, leave the product in automatic mode. Incorrect changes to the link speed and duplex settings might prevent the HP 352dw from communicating with other network devices. If you need to make changes, use the printer control panel.
NOTE:
  • The setting must match with the network product to which you are connecting (a network hub, switch, gateway, router, or computer).
  • Making changes to these settings causes the product to turn off and then on. Make changes only when the product is idle.
  1. Open the control panel dashboard (swipe the dashboard tab at the top of any screen downward, or touch the dashboard area on the home screen).
  2. On the control panel dashboard, touch .
  3. Touch Network Setup, and then touch Ethernet Settings.
  4. Touch Advanced Settings, and touch Link Speed.
  5. Select one of the following options.
Depending on your operating system, you can open the printer software as follows:
  • Windows 10: From the computer desktop, click Start, select All apps, click HP, click the folder for the printer, and then select the icon with the printer's name.
  • Windows 8.1: Click the down arrow in lower left corner of the Start screen, and then select the printer name.
  • Windows 8: Right-click an empty area on the Start screen, click All Apps on the app bar, and then select the printer name.
  • Windows 7, Windows Vista, and Windows XP: From the computer desktop, click Start, select All Programs, click HP, click the folder for the printer, and then select the icon with the printer's name.

1 comment:


  1. Nice blog...Very useful information is providing by ur blog..here is a way to find.

    123 HP OJ Pro 6835 Setup

    ReplyDelete